![]() Maybe, this will upgrade my sound to SUPER DUPER MEGA! For an even better amp sim guitar sound, I think i might switch to an Audient id4 mkii or id14 mkii. Also, I've only ever used 1 input at a time really, occasionally 2. The UR44 has been good but it is old and i don't think i'm getting the best sound from it. The only thing left to change now, is the interface. So in terms of getting a better guitar sound using amp sims, changing software = meh!, changing guitars= MEGA! and upgrading the computer = SUPER MEGA! ![]() The Strat sounded great through an amp, just not with direct in to a computer, I thought it was the interface DI, but it was the guitar. My previous Strat was too harsh and grainy for the computer but the Tele sounds warm and fat, with all the harshness gone, much better for direct recording with the computer, even when i switch to the single coils. I've got more of a respect for the amp sims now. In terms of guitar though, i swapped out the mexican Strat for a player series double humbucker Tele (with push/pull pots for single coil function) and this change really helped with the overall sound. My previous computer was dead silent, all the time. The only annoyance with the new computer, is the noise it makes, not too bad on cool days but turns into a revving motorcycle on hot days. Also, the VST pianos etc are all great now, i can play really fast parts without timing issues. Latency is a non issue and running the KU13 instruments and GR6 etc is fine. Basically, all of these problems just went away. Then i got a new computer, an 11th gen i7 with 32gig ram. But when i put KU 13 on everything ran slow, like really slow, sometimes taking 1 minute or more just to open GR6 or the new massive etc. Same thing with VST keyboards and pianos etc, although i could "get by" with these. It was almost there, but on fast guitar parts, the timing just wasn't right. Komplete ultimate 10 ran ok with it, gr5 etc although I could never get latency really acceptable with amp sims and instead, ran through pedals with direct monitoring. This is what forced me to upgrade the computer in the end. And my usage of these plugins has decreased significantly as a result. ![]() The CPU load on most of their plugins has increased significantly over the last few years. KNOWN ISSUE Dragging files from the OS into Guitar Rig causes slowdown IMPROVED Default modulation range was 75% but is now 100%įIXED Twin Delay did not sound correct when using maximum predelay/delay timesįIXED Delay time parameter display value was wrong in Sync Mode on some componentsįIXED Undoing removal of Reflektor inside a Container had no IR loadedįIXED Undoing removal of Little Reflektor component could crashįIXED Undoing component preset load did not restore preset nameįIXED Undoing Macro assignment would not update Macro UI and could cause crash if interacted withįIXED The rack preset menu now correctly loads the next/previous preset after performing an undoįIXED The component preset menu now correctly loads the next/previous preset after performing an undoįIXED Preset Volume and Metronome parameters now revert when undoing rack preset loadįIXED Some Dirt parameters were not modulatableįIXED RC24/RC48 input and output level parameters were not modulatableįIXED LFO waveform, amplitude offset and phase offset parameters were not modulatableįIXED Tapedeck volume parameters were not modulatable or controllable with macrosįIXED PresetVolume dry/wet and volume parameters were not modulatable or controllable with macrosįIXED Using the “Clear Rack” button in the rack Toolbar would not update the Macro assignmentsįIXED When a Macro knob was assigned to a button, assignment ranges were not taken into accountįIXED Bite no longer silences right channel in stereo mode when left channel is silentįIXED Guitar Rig now runs again on 圆4 processors that only support SSE3 and below IMPROVED Display CPU architecture in about box IMPROVED LFO waveforms can now be selected directly via a menu in the LFO modifier component IMPROVED Files can be on loaded onto the Tapedecks by dragging and dropping IMPROVED Container and Macro assignment sliders now have numeric value displays IMPROVED Container and Macro assignment sliders can now be controlled by the mouse wheel IMPROVED Rack now automatically scrolls to enabled fixed component if out of view IMPROVED Rack now automatically scrolls to inserted component if out of view IMPROVED Parameter changes are now undoable and redoable ![]() ADDED New ICM component: Red Fuzz, a distortion component that has 3 fuzz modes modelled from classic analog gear ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |